CrossOver Support - Community Forums

Hello,
I want to run Wires-X a software for ham radio which needs open ports that the Wires-X network has access to this application.
Therefore I setup my router and I opened the requested ports.
But the application tells me that the ports are not open.
In the first shot I tried to make it work with the visualization software UTM with installed Windows10, with success.
But it only worked when I configured the visualization in bridge mode with separate IP/MAC address for the guest. With shared mode (host and guest same IP/MAC address) I failed.
I see here a similar problem, is there a possibility to run the bottle in "bridge mode" with separate IP and MAC address to the host?
May be I have to configure something on the Mac? or on the bottle? (firewall on the MAC is off)
By the way I managed to make the modem work one USB which connects Radio to the computer
I have latest version of Crossover and Mac OS 15.3.2 installed on Mac Studio M4Max
Thanks for help!
Regards
Siegfried

Additional Information:
when I activate UPnP (self opening the port by application) which I activated in the router I get when I do port check in the Wires -X software this information with one error "Client UPnPError 401 Invalid Action" all other actions seem to work. see trailing
Thank's
Siegfried

CRouterSearch Initialize success.
Router(IGD) search

Router(Internet Ggate Device) Found
Location:http://192.168.178.1:49000/igddesc.xml
ST:urn:schemas-upnp-org:service:WANIPConnection:1

Get controlURL
http://192.168.178.1:49000/igdupnp/control/WANIPConn1

Get WAN IP-Address Start
s:Client UPnPError 401 Invalid Action

AddPortMapping Start. UDP Port:46100
UPnP Setting success

AddPortMapping Start. UDP Port:46112
UPnP Setting success

AddPortMapping Start. UDP Port:46110
UPnP Setting success

AddPortMapping Start. UDP Port:46122
UPnP Setting success

AddPortMapping Start. UDP Port:46120
UPnP Setting success

AddPortMapping Start. UDP Port:46114
UPnP Setting success
UPNP entry finished.

**On retry I gott this*****

CRouterSearch Initialize success.
Router(IGD) search

Router(Internet Ggate Device) Found
Location:http://192.168.178.1:49000/igddesc.xml
ST:urn:schemas-upnp-org:service:WANIPConnection:1

Get controlURL
Get controlURL fail..Retry

I tried it with the Netgear router with no error UPnP port opening but when I recheck the ports same result... please see theology
By the way with UTM visualization and Windows installed self port opening does not work too interesting with one port it works... With visualization it only works with separate MAC and IP address on the guest system and fixed forwarded ports
Thank's
Siegfried

CRouterSearch Initialize success.
Router(IGD) search

Router(Internet Ggate Device) Found
Location:http://10.0.1.1:56688/Public_UPNP_gatedesc.xml
ST:urn:schemas-upnp-org:service:WANPPPConnection:1

Get controlURL
http://10.0.1.1:56688/Public_UPNP_C5

Get WAN IP-Address Start
manufacturer : NETGEAR, Inc.
modelName : RAX80
External IP :
192.168.178.22192.168.178.22

AddPortMapping Start. UDP Port:46100
UPnP Setting success

AddPortMapping Start. UDP Port:46112
UPnP Setting success

AddPortMapping Start. UDP Port:46110
UPnP Setting success

AddPortMapping Start. UDP Port:46122
UPnP Setting success

AddPortMapping Start. UDP Port:46120
UPnP Setting success

AddPortMapping Start. UDP Port:46114
UPnP Setting success
UPNP entry finished.

***After retry checking ports**

Get controlURL
Get controlURL fail..Retry

Router(Internet Ggate Device) Found
Location:http://10.0.1.1:56688/Public_UPNP_gatedesc.xml
ST:urn:schemas-upnp-org:service:WANPPPConnection:1

Get controlURL
Get controlURL fail..Retry over